Rust on bottom of safe

Gun, shooting and equipment discussions unrelated to CHL issues

Moderator: carlson1

Post Reply
User avatar
olafpfj
Senior Member
Posts: 661
Joined: Sat Sep 04, 2010 12:03 pm
Location: Grapevine

Rust on bottom of safe

Post by olafpfj »

20130717_130238.jpg
I actually discovered this last October when I was moving but I haven't had time to deal with it till today.

This is most likely due to a hot water heater overflow that ran through my garage. I remember seeing the evidence that there had been some water coming from the overflow pipe in the drain pan but I didn't think it had made it to the safe. I guess it did :grumble

Just finished scraping and sanding off the worst of it and I'm going to hit it with some naval jelly. Doesn't seem too severe but it is beyond surface rust in some places. No where near rusting through though. I think I'm going to put a layer of plastic under it when I stand it back up to keep the ever present moisture from the slab from getting to it. Unfortunately the only place I can put the thing is in the garage. I've had 3 of those little rechargable de-humidifiers in it for years and despite needing to be plugged in and dried out every other week the guns all seem fine. I'm adding an electric de-humidifier into the safe as well.

If you have a safe in your garage make sure you check the bottom of it every once in a while.
"If you have ten thousand regulations you destroy all respect for the law." -Winston Churchill
flechero
Senior Member
Posts: 3486
Joined: Thu Dec 06, 2007 5:04 pm
Location: Central Texas

Re: Rust on bottom of safe

Post by flechero »

Perhaps a good coat of paint after proper prep since it was already turned over. ?
User avatar
olafpfj
Senior Member
Posts: 661
Joined: Sat Sep 04, 2010 12:03 pm
Location: Grapevine

Re: Rust on bottom of safe

Post by olafpfj »

flechero wrote:Perhaps a good coat of paint after proper prep since it was already turned over. ?
I considered that and decided against it. I have had some pretty horrific experiences with heavy painted things getting practically welded to whatever they are sitting on. Plus I figured quite a bit of it would be scratched off while my wife and I slid it back into place.

What I did instead was to give the bottom (after prep) a good liberal bath of WD-40. I also sprayed down the patch of concrete in the garage where it will be sitting with a good coat of WD-40. Hopefully this will slow down the problem till I either a: buy a house or b: buy a new bigger safe.
"If you have ten thousand regulations you destroy all respect for the law." -Winston Churchill
Dirthawking
Member
Posts: 199
Joined: Sun Jun 02, 2013 3:48 pm

Re: Rust on bottom of safe

Post by Dirthawking »

If the safe is not bolted down, why not just put something like a piece of diamond plate under it to allow for minor air flow under it?
Some people simply need a high five, to the face, with a chair!
longtooth
Senior Member
Posts: 12329
Joined: Sun Jun 12, 2005 3:31 pm
Location: Angelina County

Re: Rust on bottom of safe

Post by longtooth »

Dirthawking wrote:If the safe is not bolted down, why not just put something like a piece of diamond plate under it to allow for minor air flow under it?
I had the same issue when mine set on the garage slab. Sanded & painted again when we moved it. The air flow has worked GOOD.
Image
Carry 24-7 or guess right.
CHL Instructor. http://www.pdtraining.us" onclick="window.open(this.href);return false;
NRA/TSRA Life Member - TFC Member #11
User avatar
RogueUSMC
Senior Member
Posts: 1513
Joined: Tue Apr 30, 2013 12:55 pm
Location: Smith County
Contact:

Re: Rust on bottom of safe

Post by RogueUSMC »

http://www.instructables.com/id/Preserv ... eel-Iron-/We used this stuff years ago on pipe probes that, by law, couldn't be painted...worked great for us...
A man will fight harder for his interests than for his rights.
- Napoleon Bonaparte
PFC Paul E. Ison USMC 1916-2001
User avatar
olafpfj
Senior Member
Posts: 661
Joined: Sat Sep 04, 2010 12:03 pm
Location: Grapevine

Re: Rust on bottom of safe

Post by olafpfj »

RogueUSMC wrote:http://www.instructables.com/id/Preserv ... eel-Iron-/We used this stuff years ago on pipe probes that, by law, couldn't be painted...worked great for us...
I think I've heard of that stuff before. The safe isn't too much of a pain to tip over (yes I know...should be bolted down) so maybe I'll revisit this problem. I think the WD-40 will certainly do the trick though.

Question: There are only some small pits of rust left that I just couldn't quite sand out. Will those pits continue to oxidize and grow even after I've hit the whole thing with naval jelly and tons of WD-40?
20130717_180441.jpg
"If you have ten thousand regulations you destroy all respect for the law." -Winston Churchill
User avatar
G26ster
Senior Member
Posts: 2655
Joined: Wed Feb 03, 2010 5:28 pm
Location: DFW

Re: Rust on bottom of safe

Post by G26ster »

Paint the bottom with POR-15
User avatar
threoh8
Senior Member
Posts: 648
Joined: Tue Dec 30, 2008 5:02 pm
Location: Lubbock, Texas

Re: Rust on bottom of safe

Post by threoh8 »

We had a couple of water issues in the house, including one that went under my safe. Now, to give early warning, I use a couple of these
water leak detectors. Cheap insurance.
The sooner I get behind, the more time I have to catch up.
Post Reply

Return to “General Gun, Shooting & Equipment Discussion”